Solar Structure & Fabrication in Karachi, Built Strong
A&Z Solar Energy offers solar structure and fabrication in Karachi: elevated, L2, L3 and ground mounted structures, plus walkways, made and fixed by our own team.
Sun in, structure up: our team builds your solar structure on site.
Solar Structures For Roofs, Parking And Ground
A&Z Solar Energy builds six types of solar structure, so your panels sit safely wherever you have space.
Elevated Structure
Our elevated structure is built on the rooftop at 8 to 12 feet. It lifts panels above shade, water tanks and stairs, leaves useful space below for storage or shade, and stands strong against wind on bungalows and commercial buildings.
- Bungalows and commercial roofs
- Space below for storage or shade
- Strong against wind
L2 Structure
The L2 structure sits about 3 feet above the roof and is a simple, economical frame for open flat roofs. It installs quickly, keeps the cost down, and holds your panels firmly at the right angle for the sun.
- Open flat roofs
- Budget friendly
- Quick to install
L3 Structure
The L3 structure sits 4 to 5 feet above the roof, giving more clearance underneath. This makes panel cleaning easier, lets air move freely under the panels, and works well for busy roofs where people need to walk around.
- Easier panel cleaning
- More airflow under panels
- Good for busy roofs
Solar Walkway Structure
Our solar walkway structures are steel paths built between panel rows. Your cleaning and maintenance team can walk, inspect and clean safely without stepping on the panels. Neat, durable and made to fit any panel layout.
- Safe cleaning access
- Neat and durable steel
- Fits any panel layout
Car Parking Structure
Solar car parking structures give your vehicles shade while the panels above make electricity. They suit homes, offices and factories, turn unused open space into a power source, and are built from strong, rust protected steel.
- Homes, offices and factories
- Shade for cars
- Uses unused open space
Ground Mount Structure
Ground mount structures are strong steel frames fixed on concrete footings, made for open plots, farms, factories and large solar plants. We set the tilt for the best sun, and the panels stay easy to reach and maintain.
- Open land and large plots
- Tilt set for best sun
- Easy to reach and maintain
Structure & Fabrication: What Is The Difference?
Fabrication is the workshop work: our team measures, cuts, drills, welds and coats raw steel with red oxide and primer, so every part is ready and rust protected. The structure is the finished steel frame built from those parts and fixed on your roof, car park or ground, holding your panels at the right height and angle. In short, fabrication makes the parts and the structure is what you see standing on site. A&Z Solar Energy does both under one team, so sizes fit properly and nothing is left to chance.
Fabrication
In the workshop: measure, cut, drill and weld the steel, then coat it with red oxide and primer.
Solar Structure
On site: fix the legs, bolt the girders and rails, and mount your panels at the right angle.
What We Use To Build Strong Solar Structures
Materials depend on design, load and span. This is what we use when your project needs it.
12-Gauge Girder
The main supporting beam of the structure. It carries the weight of the panels.
14-Gauge Pole
The vertical support. We use it when the load and span suit it.
Red Oxide
An anti-rust coating on the steel. It slows corrosion and protects the frame.
Primer
The base paint layer. It helps the topcoat stick and protect the steel.
Structures We Have Built
Photos and videos of our elevated, L2, L3, ground mounted structures and walkways, made and fixed by our team.
Solar Structure & Fabrication in Karachi, Built Strong
A&Z Solar Energy offers solar structure and fabrication in Karachi: elevated, L2, L3 and ground mounted structures, plus walkways, made and fixed by our own team.
Sun in, structure up: our team builds your solar structure on site.
Solar Structures For Roofs, Parking And Ground
A&Z Solar Energy builds six types of solar structure, so your panels sit safely wherever you have space.
Elevated Structure
Our elevated structure is built on the rooftop at 8 to 12 feet. It lifts panels above shade, water tanks and stairs, leaves useful space below for storage or shade, and stands strong against wind on bungalows and commercial buildings.
- Bungalows and commercial roofs
- Space below for storage or shade
- Strong against wind
L2 Structure
The L2 structure sits about 3 feet above the roof and is a simple, economical frame for open flat roofs. It installs quickly, keeps the cost down, and holds your panels firmly at the right angle for the sun.
- Open flat roofs
- Budget friendly
- Quick to install
L3 Structure
The L3 structure sits 4 to 5 feet above the roof, giving more clearance underneath. This makes panel cleaning easier, lets air move freely under the panels, and works well for busy roofs where people need to walk around.
- Easier panel cleaning
- More airflow under panels
- Good for busy roofs
Solar Walkway Structure
Our solar walkway structures are steel paths built between panel rows. Your cleaning and maintenance team can walk, inspect and clean safely without stepping on the panels. Neat, durable and made to fit any panel layout.
- Safe cleaning access
- Neat and durable steel
- Fits any panel layout
Car Parking Structure
Solar car parking structures give your vehicles shade while the panels above make electricity. They suit homes, offices and factories, turn unused open space into a power source, and are built from strong, rust protected steel.
- Homes, offices and factories
- Shade for cars
- Uses unused open space
Ground Mount Structure
Ground mount structures are strong steel frames fixed on concrete footings, made for open plots, farms, factories and large solar plants. We set the tilt for the best sun, and the panels stay easy to reach and maintain.
- Open land and large plots
- Tilt set for best sun
- Easy to reach and maintain
Structure & Fabrication: What Is The Difference?
Fabrication is the workshop work: our team measures, cuts, drills, welds and coats raw steel with red oxide and primer, so every part is ready and rust protected. The structure is the finished steel frame built from those parts and fixed on your roof, car park or ground, holding your panels at the right height and angle. In short, fabrication makes the parts and the structure is what you see standing on site. A&Z Solar Energy does both under one team, so sizes fit properly and nothing is left to chance.
Fabrication
In the workshop: measure, cut, drill and weld the steel, then coat it with red oxide and primer.
Solar Structure
On site: fix the legs, bolt the girders and rails, and mount your panels at the right angle.
What We Use To Build Strong Solar Structures
Materials depend on design, load and span. This is what we use when your project needs it.
12-Gauge Girder
The main supporting beam of the structure. It carries the weight of the panels.
14-Gauge Pole
The vertical support. We use it when the load and span suit it.
Red Oxide
An anti-rust coating on the steel. It slows corrosion and protects the frame.
Primer
The base paint layer. It helps the topcoat stick and protect the steel.
Structures We Have Built
Photos and videos of our elevated, L2, L3, ground mounted structures and walkways, made and fixed by our team.
Solar Structure & Fabrication Questions
What is solar structure and fabrication?
Fabrication is cutting, welding and coating steel in the workshop. The solar structure is the finished steel frame that holds your panels on a roof or on the ground.
What is the difference between solar structure and fabrication?
Fabrication is the making of the steel parts. The structure is the complete frame built from those parts and fixed on site.
Do you make ground mounted solar structures in Karachi?
Yes. A&Z Solar Energy builds ground mounted structures for open land, farms, factories and large plots, as well as rooftop structures.
How high is an elevated solar structure?
Our elevated rooftop structures are built at 8 to 12 feet, which leaves space underneath and keeps panels clear of shade.
What is an L2 solar structure?
An L2 structure sits about 3 feet above the roof. It is a simple, economical choice for open flat roofs.
What is an L3 solar structure?
An L3 structure sits 4 to 5 feet above the roof, giving more clearance for cleaning and access.
Which steel do you use for solar structures?
We use 12-gauge girders for main supports and 14-gauge poles for vertical supports, where the design, load and span require them.
How do you protect the structure from rust?
We apply red oxide anti-rust coating and a primer base layer before the topcoat to reduce corrosion.
Do you build solar walkways?
Yes. We build steel walkway structures between panel rows so your team can clean and inspect panels safely.
Can you fabricate a structure to my roof or land size?
Yes. We design and fabricate to your measurements, system size and wind load after a site visit.
Need Solar Structure & Fabrication In Karachi?
Send your roof or land size and photos on WhatsApp. Our team will suggest the right structure and give you a clear quotation.
💬 Chat With Us On WhatsAppSolar Structure & Fabrication Questions
What is solar structure and fabrication?
Fabrication is cutting, welding and coating steel in the workshop. The solar structure is the finished steel frame that holds your panels on a roof or on the ground.
What is the difference between solar structure and fabrication?
Fabrication is the making of the steel parts. The structure is the complete frame built from those parts and fixed on site.
Do you make ground mounted solar structures in Karachi?
Yes. A&Z Solar Energy builds ground mounted structures for open land, farms, factories and large plots, as well as rooftop structures.
How high is an elevated solar structure?
Our elevated rooftop structures are built at 8 to 12 feet, which leaves space underneath and keeps panels clear of shade.
What is an L2 solar structure?
An L2 structure sits about 3 feet above the roof. It is a simple, economical choice for open flat roofs.
What is an L3 solar structure?
An L3 structure sits 4 to 5 feet above the roof, giving more clearance for cleaning and access.
Which steel do you use for solar structures?
We use 12-gauge girders for main supports and 14-gauge poles for vertical supports, where the design, load and span require them.
How do you protect the structure from rust?
We apply red oxide anti-rust coating and a primer base layer before the topcoat to reduce corrosion.
Do you build solar walkways?
Yes. We build steel walkway structures between panel rows so your team can clean and inspect panels safely.
Can you fabricate a structure to my roof or land size?
Yes. We design and fabricate to your measurements, system size and wind load after a site visit.
Need Solar Structure & Fabrication In Karachi?
Send your roof or land size and photos on WhatsApp. Our team will suggest the right structure and give you a clear quotation.
💬 Chat With Us On WhatsApp